A landscape lighting technician installs and services low-voltage outdoor lighting, including 12-volt systems, for landscape contractors, lighting companies and design-build firms.
The work covers path lights, uplights, hardscape and step fixtures, and holiday displays.
Federal data has no occupation code of its own for the title.
This guide covers the work, the route in, the AOLP certification, state electrical rules, pay and winter work.
What is a landscape lighting technician?
A landscape lighting technician installs, wires, aims and repairs the lighting that finishes a landscape after dark.
The fixtures run along walkways and driveways, up tree trunks and building walls, through garden beds, and across decks, steps and hardscape.
The work is electrical in character but lives inside the landscape trade, and it travels under different titles: landscape lighting installer, outdoor lighting technician, low-voltage lighting technician, and holiday lighting installer in season.
The federal data point matters to a job seeker.
BLS's Occupational Outlook Handbook notes that some landscaping workers help install lighting or sprinkler systems.
Neither the handbook nor O*NET lists landscape lighting technician as an occupation of its own, so the title has no federal employment or wage series.
Employers include landscape contractors that run a lighting crew, design-build firms that sell lighting with a build, companies that install outdoor lighting exclusively, and holiday lighting outfits that work the season.
The dividing line between a lighting technician's work and an electrician's is set by state electrical rules, not by the fixture on the ground.
Where that line sits decides what a tech may legally wire, and the training and certification section below takes it up.
What they install and service
Installation is the visible half of the job.
A tech lays out fixture locations from a plan or from their own read of the property, then trenches and buries the wire and sets the fixtures.
The wiring lands at the power unit that steps voltage down for the system.
After dark, the tech aims and adjusts each beam.
The fixture side of the trade runs from path lights and uplights to well lights in beds, step and hardscape lights, deck lighting, and downlights mounted in trees.
Controls round out an install: timers, photocells, and app-based scheduling on the systems that support it.
Service work is the other half.
A tech finds the break in a dead wire run, replaces corroded connectors, swaps failed fixtures and lamps, corrects controller schedules, and adds fixtures to systems already in the ground.
Digging comes with the territory, and it has a rule of its own.
811 says every digging project, regardless of depth, requires contacting 811 first, because some utilities are buried just inches below the surface.
Anyone planning to dig should contact 811 or their state 811 center a few business days in advance so buried utilities can be marked with paint or flags.
The properties run from residential front yards to HOA entrances, retail centers, office parks and municipal grounds.
Clients range from homeowners and property managers to the operators of the larger sites; the fixtures, wire and schedule belong to the crew.
How to become a landscape lighting technician
Classroom programs specifically for landscape lighting were not something our research could verify, so this route follows the trade as crews build it.
A new installer picks the skills up next to an experienced tech, and they compound from helper work to running installs of their own.
Get on a crew that touches lighting
Landscape installation crews, design-build firms and lighting-focused companies are the employers to approach about helper work. Helping install lighting is part of the grounds maintenance work BLS describes, so a general landscaping job can put you on lighting tasks first.Learn the system hands-on
Wire runs, watertight connections, fixture aiming and controller programming are field skills. Service calls teach the diagnostic half: finding breaks, failed connectors and dead fixtures with a meter and a systematic check of the run.Check your state's electrical line
What a non-electrician may wire outdoors is set by each state's electrical rules, and the exemptions our research found, in Oregon and Washington, are conditional. Confirm the current rules with your state's electrical board or licensing agency before you take responsibility for an install.Add a credential once you have field time
AOLP's Certified Low Voltage Lighting Technician (CLVLT) certification measures hands-on skills and technical knowledge for 12-volt lighting systems. The certification section below covers it and the design credential alongside it.Grow into lead and design work
Experienced technicians run their own installs, meet clients on site and translate a property into a lighting plan. Design is its own track: AOLP's second credential, the Certified Outdoor Lighting Designer (COLD), covers lighting design specifically.
Training and certifications for lighting technicians
The credential side of the trade is easier to pin down than its formal training, and it runs through one association.
The Association of Outdoor Lighting Professionals (AOLP) offers two certifications: the Certified Low Voltage Lighting Technician (CLVLT) and the Certified Outdoor Lighting Designer (COLD).
The CLVLT is a hands-on certification that measures real-world skills and technical knowledge specifically for 12-volt lighting systems.
The COLD covers lighting design.
AOLP offers its certifications on the two days leading up to its Illuminate conference, which its certification page listed for February 10–12, 2027 in Clearwater Beach, Florida when we read it in October 2026.
Check the current dates on AOLP's certification page.
A certification is a skills credential, not a license.
Neither AOLP certification makes lighting work legal in a state; the electrical rules decide that.
Two states show how conditional the exemptions are.
Oregon's electrical licensing statute, ORS 479.940(3)(a), exempts a landscape contracting business licensed by the State Landscape Contractors Board when it installs outdoor landscape lighting and irrigation control wiring on Class II or Class III systems not exceeding 30 volts and 750 volt-amperes.
Under the same chapter, the business must issue each installer an identification card (the form comes from the board) that the installer carries on the job site, and permits and electrical specialty code compliance still apply.
Washington's electrical rules exempt underground low-voltage landscape lighting from electrical licensing and permitting only under the conditions set in WAC 296-46B-925(8).
The power must come from a listed Class 2 power supply.
The line-voltage supply must be installed by licensed electricians, and nothing in the installation may fall within the scope of NEC Article 680 (pools and fountains).
Outside states with a written exemption like those, the picture is genuinely state by state: our research found no primary national compilation of low-voltage lighting rules, so treat any national state-count you see online as unverified.
The practical move is to ask your state's electrical board or licensing agency what it requires for outdoor lighting work before you wire a system on your own.
Confirm the rules before you wire
Landscape lighting technician pay
There is no federal wage series for this title.
BLS has no landscape lighting technician occupation (the agency's own handbook notes only that some landscaping workers help install lighting or sprinkler systems), so it publishes no wage for the role.
Our research carries no verified wage figure for the title either, so treat any pay number attached to it online with care and check which occupation or survey it actually comes from.
What the job pays in practice depends on the employer, the market and the season, and holiday work changes the shape of the year.
When you compare offers, look at the whole year: how long the lighting season runs, what winter work the employer actually has, and how the off-season is scheduled.
Treat posted pay as that employer's own figure, and ask the questions that matter in the interview: how much of the calendar is lighting, whether service calls run year-round, and what the crew does between seasons.
Holiday lighting and year-round work
Holiday lighting is one source of winter work for lighting crews.
The skills carry over from the landscape side: working at height from ladders and lifts, weather-rated connections, and the discipline of outdoor electrical work.
The calendar is what compresses: installs go up in the weeks before the holidays, displays run through the season, and takedown follows after the holidays.
Lighting service runs through the rest of the year: storm damage, dead fixtures, controller faults and property turnover all generate calls.
Snow removal with a landscape company is one way cold-climate crews fill the winter; maintenance work fills the season in milder ones.
For an installer who decides to run their own lighting or holiday work, the job becomes a business: pricing, scheduling, insurance questions and hiring.
The employer side of this site covers that step, from writing the first job ad to how you post a landscaping job and screen the helpers who answer it.
Career information, not legal advice. Electrical licensing and permit rules are state-specific and change; confirm the current requirements with your state's electrical board or licensing agency before you take on lighting work.

